Plywood Boat
Author: admin
Build a Plywood Boat with Wooden Boat Plans for Stitch and Glue
Should Plywood be Fastened to the Frames when Building a Plywood boat?
Building Boats planked with sheet plywood started around the World War II era. Before that, the adhesives used to make plywood were, in short, worthless for marine application; the plies would delaminate in a heavy fog. After the adhesives were improved, it took a long time before professional boatbuilders would use plywood because of its previous problems.
Builders of the time planked boats with solid wood with many seams. When plywood started to be used, builders logically built the same framework and attached the plywood in the same way as they had done with planks. Rarely did that work out. Boats planked with sheet plywood wouldn’t conform to the shape of a planked boat. A surface developed from a segment of a cone or cylinder was required to enable the sheet material to bend to natural curves. The method is known as “sheet plywood development”.
Most builders retained the closely spaced frames with many longitudinals and a zillion fasteners. Then someone reasoned that all that framework wasn’t required. Further down the road, many production boats were monocoque; the boats were built over a form with stem, transom, chine and sheer the only framework members. After the hull was removed from the form and righted, they were reinforced with internal framework, primarily longitudinals. This eventually led to current Stitch and Glue Boatbuilding.
But before that progression, the sheet plywood boat framework resembled that of its predecessor, the planked boat. At about the same time, more powerful motors such as the automotive V-8’s were converted and installed in the new plywood boats. This was before the advent of superior epoxy adhesives and epoxy based putties for fastener holes. At higher speeds, the putty over the countersunk fasteners would come out, water would catch the outer plywood lamination and eventually rip out the outer plywood lamination, starting at the screw hole.
This condition was primarily observed across the plywood at frames that contacted the bottom, longitudinal fasteners caused minimal problems. The logical solution was to eliminate cross fastenings in the bottom frames, and it worked. Some builders even went so far as to relieve the frame so it had no contact to the bottom planking. This also worked well and today is quite common in faster sheet plywood boats, although in slower boats the frame contacting the planking is still prevalent. However, fasteners are preferably NOT used across the planking in any sheet plywood boat.
Fairing a sheet plywood boat framework so the planking will perfectly contact the frames is wonderful in theory, but virtually impossible in practice. The frame will either contact the planking causing a hard spot or the reverse. In many sheet plywood boats, side battens were eliminated or minimized and this accentuated any out of sync frame. Fasteners driven into an out of sync frame causes a visible bump or dish that will mirror through the finished planking.
This becomes more visible on dark painted sheet plywood planked sides. Eliminating fasteners and relieving the frames so they did not contact the plywood solved the problem. Many die hard builders and older texts still retain the notion that sheet planking should contact frames. The latest practice allows the sheet plywood to take a natural bend; it isn’t being forced against framework to form an unnatural compound curvature.
Many have questioned why we do not advocate fastening into the frames on sheet plywood boats. The foregoing is our reasoning and is proven in practice. A boat built using the described procedures will not have bumps or hollow spots or framework mirrored to the outside. It’ll be a smooth uniform surface and even black painted hulls are practical. Plus, it’s proven to be durable. Why build any other way?
About the Author
Gayle Brantuk is the Vice President of Glen-L Marine Designs in Bellflower, California. Since 1953, Glen-L has provided boat plans, Boat Kits and supplies for the beginning builder to build their own boat. Visit the Glen-L online Catalog to see over 300 boats you can build:
http://www.boatdesigns.com/Boat-Plans-Kits-Catalog/departments/2/
All rights reserved, Copyright Glen-L Marine, 2010
plywood boat
|
|
Knape & Vogt P2417TAN48 Plastic Sliding Door Track And Guides $5.23 48″ plastic track and upper guide assembly. Installs with contact cement, 2-sided carpet tape, tacks, or screws. Can be cut to any length, surface mounted or recessed in a dado. Tan color…. |
|
|
Gilmour 12 Series 5 Ply Marine & Recreation Hose 5/8 Inch x 75 Feet12-58075 White w/Aqua Stripe $39.99 These extremely durable drinking water safe hoses are ideal for use on boats, campers, and for other recreational activities. The 5-ply construction makes them extremely abrasion resistant and virtually impervious to bursting, and the blue-striped white cover wont mar surfaces. They are extra kink resistant, flexible, and easy to coil in all weather conditions. Full-Flo brass couplings allow fo… |
|
|
Gilmour 12 Series 5 Ply Marine & Recreation Hose 1/2 Inch x 25 Feet 12-12025 $10.94 5-ply construction, high burst strength FDA approved liner material for drinking water safety. Nickel plated couplings are drinking/potable water safe. Full-Flo brass couplings for unrestricted water flow. EZ-On coupler on 1/2″ hose. EZ-On coupler on andprotective collar on 5/8″ hose. Extra kink resistant, flexible and easy to coil in all weather. Durable, blue-striped white cover won’t mar surfac… |
|
|
Building the Touryak Step by Step Guide for Touring Kayak $19.95 “Carolina kayak designer Ralph Beer adopted design and construction techniques from the high performance Surfyak surf kayak (www.surfyak.com) into a lightweight, easy to build touring kayak. The Touryak 12 is a delight for paddlers of all skill levels to paddle. The wide, flat bottom floats you high so you can explore the shallows. The sharp rails make this boat track straight and true. Even begin… |
|
|
Intex Motor Mount Kit $20.30 Intex Motor Mount Kit lets you attach up to a 3.5-horsepower motor to the rear of your Intex boat, so you can rest your paddling arms and float in comfort. The mount–which is made of marine plywood with aluminum support arms–attaches and detaches easily, so you don’t have to spend a half hour fussing with the components each time you want to use the motor. Plus, the mount disassembles quickly wh… |
|
|
KidKraft Pirate Sandboat $189.95 KidKraft Pirate Sandboat. A swashbuckling sensation for in – the – yard excitement! Shiver me timbers! This Pirate Sandboat is the perfect place for your little swashbucklers to enjoy a day of play! And with a large 75 x 44 1/2 x 52″ size, this Sand Box is big enough for a few friends to join in on the fun. Features a shady canopy to keep kids out of the sun, and colorful, creative pirate detailin… |
|
|
Sailboat Woodcraft Construction Kit $5.59 This is a Woodcraft Construction Kit of a Sailboat. There are 39 interlocking 3mm wooden plywood pieces and when assembled measure 12 1/3″ L x 6 3/4″ W x 1 3/4″ H. These Woodcraft Construction Kits are 3D wooden puzzle marvels for kids of all ages. Not only are they fun to put together, but they are also educational and bring out the creativity of those working on them. The units are made of 3mm p… |
|
|
Highland 2005200 48 Black Universal Car Top Bar Carrier $27.28 Highland Group Industries 20052 Univ Superfit Bar Carrier… |
|
|
Extend-A-Truck 944 Truck Bed Extender $86.62 Lengthen your truck with the Extend – A – Truck 2 – in – 1 Load Support. Fits 2″ receiver hitches, installing in seconds! Use it upright for roof-level support or horizontally to increase your truck bed’s usefulness in an instant! Lumber, big boxes, ladders, kayaks, canoes… the heavy tubular steel supports loads up to 350 lbs. safely and securely. Done hauling? It conveniently folds flat for sto… |
|
|
Buehler’s Backyard Boatbuilding $13.69 Everybody has the dream: Build a boat in the backyard and sail off to join the happy campers off Pogo Pogo, right? But how? Assuming you aren’t independently wealthy, if you want a boat that’s really you, you gotta build it yourself. Backyard boatbuilding has its problems. Building in fiberglass is itchy, smelly, and yields a product that yachting maven L. Francis Herreshoff once called “frozen… |
Tags: boat, boatbuilding, boats, diy, plans, plywood boat, plywood boat building, plywood boat construction, plywood boat kits, plywood boat plans
